ploughmonday41

How to Replace a Kia Sportage Replacement Key The key in many Kia models comes with an entry system that is keyless into. The key can be compared to the remote control and is able to be replaced with a fresh one from a Kia dealer or locksmith. Key fobs are prone to malfunction for several reasons, including an empty coin battery, worn buttons, signal interference, water damage and a faulty receiver module. Here are some helpful tips on how you can get your Kia Sportage replacement key back to working. How to replace a remote key or smartkey Whether your Kia is equipped with an intelligent key, remote key push to start key or a regular non-transponder steel key The battery inside these keys will eventually require replacing. This is particularly relevant if your car displays a message that the remote or smart key has a low battery. Luckily, this is an easy procedure. To replace the keyfob battery take out your mechanical key from the slot at the back of the fob. Then, push the cover open. A small screw will be in the key fob to keep the battery in place. Take out the old battery by unwinding the screw using a small screwdriver. Insert the new battery and close the opening on the key fob. Test the key fob by pressing the lock or unlock buttons. It's okay if the doors lock and unlock as you expect. You can now make use of the hands-free lock/unlock feature on your Kia whenever your fingers get chilly or you need to make errands in Brandon. Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll have to record the key code number on the key code tag. How to replace the battery If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a good indicator that the battery should be replaced. A weak battery can cause other issues, such as the check engine light turning on or the engine not cranking. Fortunately replacing the key fob battery is a relatively easy DIY project that requires just some basic tools. Be sure to turn off your vehicle and close the doors before you begin. Find the small, metal or plastic piece on the bottom of your key fob, and jiggle it until a metal key is released. This key can be inserted into the driver door handle to unlock your car. To replace the key fob battery, take off the cover on the rear and use a pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and orient the new battery so that the “+” positive side faces you, and the “negative” negative side is facing the fob's electronic contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts. Once kia keys g28carkeys.co.uk has been installed then turn the key fob off and on in the ignition repeatedly until the door locks cycle. Then you can test your Kia key fob to check whether it's functioning properly again. How to replace the smart key Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference between the two is that the smart key is equipped with tiny mechanical key blade in it, whereas the standard fob doesn't. Both types of key fobs have a battery inside them which eventually needs to be replaced. It is a simple process that takes only two minutes. Before you get started it is important to ensure that you are on a level surface with good lighting and that your Kia is turned off. Also, keep in mind that there are tiny parts inside the fob that can fall out if you are not vigilant. The first step is to find the small release button that is located on the lower backside of the fob. It will be either an oval silver button or a rectangular slot. When you press it, the mechanical key blade will come out and you can then open the key fob. Once you have the key fob opened then you can remove the old battery, and replace it. The new battery is a C2032, and can be bought through the internet or at a local auto parts store. After you're done, your key fob should be able to lock and unlock your vehicle, even if it isn't running. How do you replace a mechanical key The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car by pressing a button. But like any device it will encounter issues from time to time. Luckily, there are steps that can be taken to fix these issues and ensure that our key fobs are in good working order over the long haul. A dead or low-quality battery is one of the most common problems. This can cause the fob to stop working altogether or to work intermittently. If this is the case, try replacing the battery with a new one. If this isn't enough to solve the problem, use a flathead screwdriver standard to wedge the fob's plastic casing open. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed, replace it with a brand new one. Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to make sure it is working properly. If the fob isn't working, contact a dealer or locksmith to help solve the issue. Make sure they cut you an emergency key that functions in all the trunk and door cylinders in order to avoid future lockouts.